Paste the RFQ, list the devices, or just name the loads (“a panel for three pumps”). The engine sizes the starters, drives, main, PLC, power supply, enclosure and cooling, checks the SCCR against the available fault current, and prices it from your price book. Every check and every number comes from your rules, never from a guess.
UL 508A control panels — breaker schedules, enclosure ratings, and heat loads checked before pricing.
Switchgear and MCC-sized jobs go to your engineers for review, with the details already gathered.
From quote to submittal: the same quote produces the submittal sheet your customer approves before the PO — ratings, a dimensioned layout, a one-line diagram and the bill of materials.
A price-book quoting tool makes sure nothing is left off: the ferrules, the duct, the label, the crate. That matters. But it can’t tell you the panel is wrong: starters rated 5 kA on a 22 kA service, a main sized from the wrong motor currents, a filtered fan on a NEMA 4X door. Those mistakes cost more than a missing line, and they surface at inspection, after the PO.
Nteli checks both. It prices the whole panel from your price book, and it checks the panel against UL 508A and the NEC before the price goes out, with the code section or catalog page behind every size and every refusal.
Buying guide: what UL 508A quoting software must check. Comparing tools? CostBook, PanelShopOS, QuotePlan and Nteli, side by side.
From $99 a month per shop — 14-day free trial, no card needed. Pricing
The web version. 14-day free trial, no card needed.
Up to 3 quote builders.
Unlimited quote builders.
Both include SCCR and NEC checks, your price book and submittal sheets. In ChatGPT or Claude, the connector stays free to use; Nteli is paid only when an order is won through it.
The engine is a full MCP server — connect it to ChatGPT or Claude and your team quotes UL 508A control panels in plain conversation, on a rule pack built from twenty years of configuring these products. Override the pack with your own rules, governed and audited — and you're onboarded.
Install Nteli Quoting in ChatGPT (or connect it in Claude), then paste any of these. They were run on the live engine; prices are illustrative until your price book loads.
What you’ll see: It won't guess the available fault current — it prices the panel and holds for that site fact; given 35 kA, it moves to a 35 kAIC main and marks the panel SCCR. And because fans aren't allowed on 4X, the enclosure gets an air conditioner.
What you’ll see: Starters are rated 5 kA as standard, so at 22 kA it adds a Class J/CC fuse kit to every starter and a high-interrupting main — the SCCR catch happens before the panel floor.
What you’ll see: PowerFlex drives run hotter than the default, so at a 40 °C design ambient the engine moves to a larger enclosure to keep the cooling honest — and adds the heater with its control-power load.
Both. Estimation works out what the panel costs to build; the quotation is the price your customer sees. From one request, the engine sizes the components, checks them for SCCR and NEC, estimates the cost from your price book, and turns it into a customer quotation with a submittal sheet.
Software that turns a panel request into a priced quote for an industrial control panel built to UL 508A. Most tools make sure nothing is left off the quote. Nteli also checks that the panel is right: motor currents from NEC Table 430.250, the main sized to NEC 430.24 and 409.20, SCCR against the available fault current, and enclosure cooling rules, before a price goes out.
Yes. It compares each starter's and drive's short-circuit rating with the available fault current and the main breaker's interrupting rating at the supply voltage. At 22 kA, for example, standard 5 kA starters get Class J/CC fuse kits and the main moves to a high-interrupting breaker. If the fault current isn't in the RFQ, it prices the panel and holds the quote for that site fact instead of guessing.
Yes. Prices are illustrative until your price book loads; after that every line is priced from it, and your own rules can override the starter rule pack, governed and audited.
No. It works before design: from the RFQ, a device list or the loads. The same quote produces the submittal sheet your customer approves before the PO, with ratings, a dimensioned layout, a one-line diagram and the bill of materials. Detailed design stays in your CAD tool.
Switchgear and MCC-sized jobs go to your engineers for review, with the details already gathered. Panels for Class/Division or Zone locations are quoted on the hazardous-area line.
The web version for panel shops is $99 a month per shop for up to three quote builders, or $199 a month for unlimited builders. Start with a 14-day free trial; no card is needed. Used as a connector in ChatGPT or Claude, it stays free to use, and Nteli is paid only when an order is won through it.
The four manufacturing levers · Estimate your leak ledger · The assumptions, explained · The Leak Ledger Workshop
One you quoted recently, names removed. You’ll get back what the engine produces — compare it with yours. No deck, no pitch.
Email an RFQ →