Medical gas estimating software: what an NFPA 99 quote must check, from manifold to headwall.
Who this guide is for
Specialty manufacturers of medical gas equipment (manifolds, zone valve boxes, alarm panels, station outlets, headwalls and booms, medical air and vacuum source equipment) and the distributors and installers who quote them into hospital and outpatient projects. On a typical job the request arrives as a Division 22 specification section (MasterFormat 22 60 00, gas and vacuum systems for healthcare facilities), a headwall schedule under 10 25 13 (patient bed service walls), a set of drawings and an email that says “please quote by Friday.”
Why medical gas quotes go wrong
The products are standard. What goes wrong is how they fit together on one project, and each miss gets found at submittal review, at install, or at verification, where the fix comes out of margin:
- A gas is missing from the count. The drawings show oxygen, vacuum and medical air, but the operating rooms also need nitrogen, nitrous oxide or waste anesthetic gas disposal (WAGD), and the quote only covers three of five.
- The outlets don’t fit the hospital’s equipment. The quote picks one connector style for a renovation in a facility that already uses another, so every flowmeter and regulator on the floor needs adapters or replacement.
- Headwalls and the gas system are quoted separately, by different people, and the outlet count per bed in one doesn’t match the other.
- Zone valves and alarms are counted from the drawings, not the design rules, so an area alarm, a sensor or a master alarm tie-in goes unquoted.
- Source equipment is sized from outlet count alone, without the demand assumptions, reserve supply or redundancy the system category calls for.
- Qualified labor and verification aren’t scoped, so it’s unclear whose credentials, testing and third-party verification the price includes.
- The quote and the submittal disagree, because they were built twice from different revisions.
What a medical gas quote must check
These are public standards, not secret sauce. The skill is in applying them to every line of every quote, consistently, under deadline. One caution up front: requirements differ between editions of NFPA 99, and the edition that applies is the one your authority having jurisdiction has adopted, which is often not the newest.
1. Risk category and system category (NFPA 99)
NFPA 99, the Health Care Facilities Code, sorts spaces into four risk categories by what a system failure would do: Category 1, likely to cause major injury or death; Category 2, likely to cause minor injury; Category 3, not likely to cause injury but may cause discomfort; Category 4, no impact on patient care. The facility’s risk assessment assigns them. NFPA 99’s gas and vacuum chapter then has separate requirements for Category 1, 2 and 3 piped systems, stepping down from one to the next; there is no Category 4 gas system. Category 3 systems are not used where general anesthesia or deep sedation is given. The category is the first fact a quote needs, because it shapes the source equipment, the alarms and the redundancy.
2. Gas types and outlet compatibility
A hospital project can involve oxygen, medical air, nitrous oxide, nitrogen, carbon dioxide, medical-surgical vacuum, WAGD and instrument air, each with its own color and label. NFPA 99 requires station outlets to be gas-specific, so equipment for one gas cannot connect to another. Within that, facilities standardize on a connector style, either DISS (the Diameter Index Safety System, CGA V-5) or one of several manufacturers’ quick-connect families. On new work the style is a spec decision. On renovations it has to match what is already on the walls and in the equipment room.
3. Zone valves and alarms
- Zone valves let staff shut off gas to one area in an emergency without shutting down the building, so they are placed where they can be reached quickly, in boxes with a removable cover or window, and labeled with the gas and the area served. Operating suites, critical care units and inpatient wings each get their own.
- Area alarms watch line pressure and vacuum for critical care areas and anesthetizing locations, typically at the nurse station that serves them.
- Master alarms watch the source equipment and main lines. NFPA 99 calls for at least two master alarm panels in separate locations, one of them where it is continuously observed.
- Local alarms sit at the source equipment and report to the master alarms.
For a quote, this means zone valve boxes, alarm panels, sensors and the tie-ins between them are counted from where the design rules put them, and each device’s gas list matches the gases it serves.
4. Source equipment sizing inputs
Manifolds, bulk systems, medical air compressors and vacuum pumps are sized by engineering calculation, not by catalog page. The inputs a quote has to capture are the outlets and their room types, the simultaneous-use (diversity) assumptions, peak demand, the required delivery pressure or vacuum level, the supply mode (cylinder manifold, bulk liquid or on-site generation), reserve supply, and expansion allowance. NFPA 99 requires medical air and vacuum sources to meet peak calculated demand with the largest unit out of service, and manifolds to switch from a primary to a secondary supply. Bulk oxygen storage also falls under NFPA 55. If the request doesn’t state these facts, the right move is to ask for them, not to assume them.
5. Qualified people: the ASSE 6000 series
The ASSE/IAPMO/ANSI Series 6000 (current edition 2024) sets the professional qualifications NFPA 99 relies on for medical gas work: 6010 installers, 6020 inspectors, 6030 verifiers, 6040 maintenance personnel, 6060 designers, plus 6015 and 6035 for cryogenic central supply installers and verifiers. For a quote, that means stating who installs, who performs the installer’s own testing, and whether the third-party verification by an ASSE 6030 verifier is included or excluded. It is a scope line, and leaving it vague is how disputes start.
6. Room programs and the FGI Guidelines
The Facility Guidelines Institute’s Guidelines for Design and Construction set minimum oxygen, vacuum and medical air outlets by room type, and many states adopt them, sometimes with their own additions. Owners often ask for more than the minimum. Headwall and boom quotes depend on getting this right per bed, and the electrical side of the same headwall follows NFPA 99 and NEC Article 517.
One honest boundary: a quoting tool checks the configuration; it does not certify the system or replace verification by a qualified medical gas verifier. The adopted code, the engineer of record and the authority having jurisdiction still decide.
Medical gas estimation vs. quotation
People use the words loosely, but they are two steps. Estimation works out what the job costs you: manifolds, zone valve boxes, alarms, outlets, headwalls, source equipment, pipe, labor and verification, each priced from your own price book. The quotation is what the customer sees: price, scope, exclusions, lead times and the submittal package. Medical gas estimating software that skips the standards checks produces a confident estimate for a system that fails submittal review or verification. The useful kind does both steps from one set of facts, with the checks in between, so the quote and the submittal can’t drift apart.
Spreadsheets vs. CPQ vs. a checked-quote engine
Spreadsheets are where most medical gas quoting lives: free, familiar, and dependent on the one senior estimator who knows which gases each room needs and which connector style each hospital uses. The checks live in that person’s head.
Traditional CPQ, the kind large manufacturers run, can encode option rules, but it assumes a dedicated team to author and maintain them and a seller clicking through a configurator. Most CPQ checks that a quote is complete (every option picked, every combination allowed), not that it is correct for the space it serves. Our guide on which quoting tools check engineering before pricing covers that difference.
A checked-quote engine takes the request as it arrives (spec section, schedule or email), asks for the facts that are missing, checks the configuration against rules your team has approved, then prices from your price book. Every check and every number traces to a source, so an engineer can trust it or challenge it without re-deriving it.
That’s what Nteli’s medical gas quoting software does: manifolds, alarms, outlets and headwalls, with pipeline sizing, quoted as one system by conversation. It checks the configuration; it does not certify the system or replace verification by a qualified medical gas verifier. The same engine quotes other engineered products; see all the demos.
See a medical gas system quoted end to end.
Watch the engine quote manifolds to headwalls as one system, or book a call and bring a recent project request, names removed.